HP DESIGNJET T1300 SERVICE MANUAL PDF

Manuals or user guides for your HP DesignJet T in Printer. HP DesignJet T and T Printer Series. Using your The only warranties for HP products and services are set .. Web Services manual configuration. Service Manual and more parts for CRA DesignJet t in eprinter.

Author: JoJojin Meztijin
Country: Pakistan
Language: English (Spanish)
Genre: Photos
Published (Last): 18 November 2007
Pages: 133
PDF File Size: 17.50 Mb
ePub File Size: 10.20 Mb
ISBN: 224-2-81347-176-6
Downloads: 51099
Price: Free* [*Free Regsitration Required]
Uploader: Kikora

All rights are reserved. Removal of the other two sections is done in the same way. Emergency firmware upgrade with USB flash drive Perform the Sensors Test to troubleshoot the problem further.

Asia Desighjet and Oceania. Page 33 To insert a new printhead first remove the orange protective caps. The Touch Control Panel prompts you to confirm that the dummy printheads are correctly inserted. Erasing the Hard Disk drive using either of the Secure Sanitize Levels is a very slow process, 6 hours for the 1 Pass mode and 40 hours for the 5 Pass mode. Disconnect grounding cable A and remove two T screws that secure the Scanner Motor. If you have removed or replaced product components, check the Service Calibration Guide to Removal and Installation on page If the amount of memory that the product needs to process the file is more than the amount available, the product will display this system warning.

The product now tries to align the printheads. Release the four attachment clips.

Extract gp right side of the cleanout, as shown, and then the left side. Left Hand Assemblies on page Insert the new purgers, reconnect the power cord and power on the product.

  KKNK PROGRAM PDF

Remove the freewheel assembly. Before using this chapter to remove and install a new component, always make sure that you have performed the relevant service test from Chapter 4. Product sold by third party: Cleaning the Glass Plate The customer is recommended to clean the glass plate periodically, depending on the usage of the product.

Push the knot of the cable in the direction of the arrow if needed. When you have loaded the paper, press OK. Press OK to continue and return to the menu.

HP Designjet T790 T1300 T2300 Series Service Manual

For instructions to enter the service calibrations menu, see Entering the Service Calibrations Menu on page You can use the Flex Contacts Cleaning Tool. Rewinder Adjust The Rewinder Adjust utility clears the calibration parameters associated with a Rewinder motor when it has to be replaced.

The product starts checking and preparing the printheads. The basket was damaged during the product setup There are three plastic parts that could break during product installation and need replacing.

The photo shows the in product, which has one spacer just above the red manial. Paper Path Asse mblies Front on page Disconnect the paper sensor cable connector. Screw the pinch arm assembly to the roll cover. Carriage Assembly on page Remove all the Printheads.

DESIGNJET T/T ePrinter series & T eMFP series Service manual

Close the Carriage Cover. The product makes some further checks. Page 98 The following screen is displayed. Unplug the Upper Right Roll Support, taking care not to damage the cables.

  LEGO 7725 PDF

HP Designjet T790 / T1300 / T2300 series. Service Manual

Check the condition and connections of the Scanner Power cable, if necessary replace the cable. Entering the Diagnostics Menu Make sure the product is switched off with the Power key on the side of the Touch Screen Panel, and not with the power switch on the back of the product.

Warranty removed from product: Sensor and belt Scanner Motor Assembly. After removing Right and Left Wall Spacers, here are the removed parts.

HP Designjet T T T Series Service Manual | eBay

Emergency firmware servie with USB flash drive on page Remove the deflector assembly. The PRS subsystem is designed to move the carriage assembly between two predetermined vertical positions with respect to the plane of the print platen.

Therefore, you are recommended desiynjet proceed in the following order. Left Cover Removal Switch off the product and remove the power cable. Remove the Right Cover from the product. A firmware upgrade will not always solve the problem. Remove T screw that secures the Taco Wheel and remove. There are currently no known cases when this will be needed, but it may help some users experiencing unexplained connectivity failures on embedded LANs.