Graupner: MC, MC, MC, MC, MC, MC, MC, MC/20, es in Übereinstimmung mit dieser Anleitung mit vorgeschriebenr Spannung. Bowdenzuginnenrohr auf 15mm ab und kleben diese mit Sekundenkleber in den passen Sie den Ausschlag über den Sender an (Computersender der mc. Thank you very much for purchasing the Graupner mc HoTT .. 15 / _jh_V1_de. PC COM Port connection. Through this socket it is also possible to.
|Published (Last):||17 September 2015|
|PDF File Size:||14.85 Mb|
|ePub File Size:||16.94 Mb|
|Price:||Free* [*Free Regsitration Required]|
Pitch Curve Pitch Curve Low, Middle, High access via Set-Up Menu Four different profiles for the collective pitch Setting response can be adjusted and vraupner up in flight by After selection of the point required using the external switches. Three curves are available for button and operation of the appropriate CH SEL normal flight under motor powerand a separate Page of Go.
Page 53 Fixed Wing Models I upgraded my MC with 4 3-way switches: Page 45 Fixed Wing Models If the System Menu is active, press twice. Described on page For Delta models, “DLT” combines the functions of Ailerons and Elevators, where the servos are connected to receiver outputs 2 and 3 Throttle to 1, Rudder to 4.
The error message is cleared by pressing any key. Graupnrr if You have some directions for me don’t hesitate to tell me. Depending on the external switches connected, functions can be switched on and off. Page 87 1 Yes You are right and it’s a good idea. Possibly only useful to activate mixing programs on the MC, on my MC i can also use them channels.
Descending Flight Setting Alternative Flight Setting Important Notes During the previous setting it was assumed that any For special applications you can program an Before starting the engine you should make sure that external switches possibly attached for throttle and alternative flight setting, which can be switched to throttle selector switch is in the start position, pitch curve change-over were in the basic position, Page 85 Receiver Requirements Note: A switch connected to socket 7 of the transmitter board, allows this function to be changed between two options “SF0” Pitch Curve Pitch Curve Pitch Curve Low, Middle, High access via Set-Up Menu Four different profiles anleiitung the collective pitch Setting response can be adjusted and called up in flight by After selection of the point required using the external switches.
The Transmitter can be determined by the crystal. What can I do?
PHPDL – PHP Directory Lister
Enter text anleittung picture: I know was made around year not OLDhuhand I thought is my last chance to open a thread here about these RC station. Page 3 Mixers, etc.
I spend almost 2 nights in order to find a way to correspond with someone grajpner with NO success. Also See for mc Programming handbook – 10 pages Programming manual – pages Operating instructions manual – 49 pages.
Any information is valuableso Please feel free to share with me what ever You have. Page 95other small accessories or to accommodate sunglasses etc.
GRAUPNER mc-16 Programming Manual
Don’t have an account? Operating Instructions Changes of the HF channels: Page 9 Fasten the NAUTIC modules Length adjustment of the control sticks Assembly of the Transmitter Carriers Insert the module into the intended location and that The length of the control sticks can be adjusted up to The transmitter can be equipped with the transmitter check it fits correctly.
Page 7 or recharge. Is gonna be used for an RC submarine project. I thought maybe was made only pieces and nobody cares to put on internet some info. Can some one help with that? This is fitted next to the ableitung. Only crystals of the The Transmitter case is pre-drilled for the installation operated on different frequency bands by changing correct type and the appropriate frequency band may of the modules, like NAUTIC, Proportional and Page 97 This is fitted next naleitung the receiver.
If I could find wit a long or flat arm wheel be nice. Practical Procedure Basic Adjustment If that is not the case, then one proceeds as follows: Page 71 Descending Flight Setting Alternative Flight Setting Important Notes During the previous setting it was assumed that any For special applications you can program an Before starting the engine you should make sure that external switches possibly attached for throttle and alternative flight setting, which can be switched to throttle selector switch is in the start position, pitch curve change-over were in the basic position, The switching function, described in 2.
All connectors are 2. Also included is a ready made mixer for Elevator Flap mixing. Graypner Menu General notes if necessary also over Ailerons. The default, Example 1: