ASTM A666 PDF

L Stainless Steel Sheet. ASTM A Characteristics. / L stainless steel sheet exhibits high strength, toughness and high temperature resistance. The following alloys meet the ASTM-A standard. Select an alloy for product specifications: stainless steel provides high strength and good ductility. ASTM A Standard Specification for Annealed or Cold-Worked[1] _机械 /仪表_工程科技_专业资料。ASTM A Standard.

Author: Arashirn Kejas
Country: Republic of Macedonia
Language: English (Spanish)
Genre: Photos
Published (Last): 18 January 2017
Pages: 41
PDF File Size: 4.62 Mb
ePub File Size: 18.3 Mb
ISBN: 680-5-23119-760-4
Downloads: 14837
Price: Free* [*Free Regsitration Required]
Uploader: Malajas

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

B Type is generally produced with a chemical composition balanced for rich side Type or lean side Type austenite stability depending on the properties required for speci? An alternative method of determining? The specimens shall be subjected to tension test, free-bend test, and controlled-bend or V-block test. Only annealed conditions of grades speci? The values obtained in this manner should not, however, be taken as the actual yield strength for 0.

A number in parentheses indicates the year of last reapproval.

ASTM A666 for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

The noncontrolling factor normally asgm exceed considerably the speci? Historical Version s – view previous versions of standard. ICS Number Code Material Test Report and Certi? The choice of test method for materials in conditions other than annealed shall be at the option of the seller.

  GOULDNER 1960 NORM RECIPROCITY PDF

ASTM A for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. However, in the case of dispute, tests shall be made by pressure. B Maximum unless otherwise indicated. Your comments will receive careful consideration at a meeting of the responsible technical a66, which you may attend.

Hard Elongation in 2 in. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. A superscript epsilon e indicates an editorial change since the last revision or reapproval.

The values given in parentheses are for information only. This revision of Speci? Link to Active This link will always route to the current Active version of the standard. Number of Tests 8. In case of dispute, the offset method of determining yield strength shall be used.

Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties. Originally approved in Current edition approved Oct. This standard has been approved for use by agencies of the Department of Defense. One bend test shall be made from one end of each coil.

It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. Mechanical properties such as yield strength, a666 strength, elongation, hardness, and bending shall be determined. C Annealed material that naturally meets mechanical properties may be applied. This specification covers austenitic stainless steels in the annealed and normally required cold-worked conditions.

  ECONOMIA FISCHER DORNBUSCH SCHMALENSEE PDF

D PSS means plate, strip, sheet. Last previous edition approved in as A — Only annealed conditions of grades ashm approved by the ASME code are permitted for pressure vessel use. They shall be formed in different shapes such as sheets, strips, plates and flat bars.

This abstract is a brief summary of the referenced standard. HardC Elongation in 2 in. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Rockwell B 95 95 A — 03 Standard Speci? If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. The steels shall adhere to specified chemical composition requirements. The values given in parentheses are for information only.

Specimens shall be bent around a diameter equal to the product of the bend factor times the speci?