ALLEN BRADLEY 1305 VFD MANUAL PDF

However, using an Allen-Bradley motor with your drive removes the . Н Installation guidelines called out in Appendix D of the User’s Manual. Installation Instructions IN. May, Allen-Bradley. Dynamic Brake. Cat. No. KAA KBA03, KBA06, KBA Table of Contents. Find great deals for Allen Bradley Adjustable Frequency AC Drive User Manual. Shop with confidence on eBay!.

Author: Yorr Daigrel
Country: Lebanon
Language: English (Spanish)
Genre: Software
Published (Last): 11 November 2004
Pages: 137
PDF File Size: 11.81 Mb
ePub File Size: 3.47 Mb
ISBN: 797-5-14810-735-8
Downloads: 58979
Price: Free* [*Free Regsitration Required]
Uploader: Fezilkree

Allen Bradley Adjustable Frequency AC Drive User Manual | eBay

Inspect to ensure that the ambient temperature limit has not been exceeded. An attempt has been made to set the [Run Boost] parameter to a value greater than the [Start Boost] parameter.

Skip frequencies and skip bandwith eliminate all operating frequencies. Power Test Fault – F46 Fault detected during initial start-up sequence. Check for proper mounting and spacing.

Replace the Communication cable.

Allen Bradley Adjustable Frequency AC Drive AB

The Adjustable Frequency AC Drive is a variable speed drive designed to control the speed of three-phase AC induction motors in a variety of demanding applications where flexibility, performance and ease of use are essential. Capabilities of drive are different than the master drive.

Extend the deceleration time or instal dynamic brake option. Check the external potentiometer circuit at TB2, terminals 1, 2, and 3 for a disconnected current. Inspect for breaks in communications line. DC Braking cannot be used with a synchronous motor. Connect proper adapter or change active frequency source. A longer acceleration tiime or a lighter load may be required. Phase V Fault – F39 A phase to ground fault has been detected between the drive and motor in this phase.

  INTOXICACAO DIGITALICA PDF

Unplug the HIM from the cable vfdd drive and reconnect it.

Reset to Default Parameters and Cycle power. If not, manually program any remaining parameters. The Adjustable Frequency AC drive is available with ratings 0. Fast repairs at low costs. Bus overvoltage can also be caused by motor reeneration. Error 4 – Saved data for parameter not correct for new drive. If the motor is drawing excessive current, the motor load is excessive and will not allow the drive to accelerate to set speed.

No valid operating frequency. Check cable connection from main control board to power board. Overload Fault – F7 Internal electronic overload trip. Check for a short circuit at the drive output or excessive load conditions at the motor.

Check for external noise sources. Overtemperature Fault – F8 Temperature sensor detects excessive heat.

Serial Fault – F10 An active local bus adapter is disconnected while it possesses control of a local bus function. Error 2 – The number of parameters in saved profile does not equal master number.

Allen Bradley 1305 Adjustable Frequency AC Drive User Manual

May occur on power-up. Check for broken wires, loose connections, or transducer loss at mA input, TB2. Check the motor and external wiring to the drive output terminals for a shorted condition. An active local bus adapter is disconnected while it possesses control of a local bus function. Check 130 Freq] and [Maximum Freq] parameters.

  ASCULTA-TI INIMA SANDRA BROWN PDF

Open Pot Fault – F9 An external pot is connected and the ground lead of the pot manial disconnected, creating a potential drive overspeed hazard. Motor Stall Fault – F6 The motor has stalled If the motor is drawing excessive current, the motor load is excessive and will not allow the drive to accelerate to set speed.

Hz Err Fault – F29 No valid operating frequency. Phase W Fault – F40 A phase to ground fault has been detected between the drive and motor in this phase. Drive Reset Fault – F22 May occur on power-up.

Reset your drive to the factory default settings. DC Bus voltage fell below the minimum value.

1305 AC Drives

Inspect the motor and external wiring to the drive output terminals for a shorted condition. Error 5 – Drive is running while attempting download.

Phase U Fault – F38 A phase to ground default has been detected between the drive and motor in this phase.

Verify that the parameter has been programmed correctly. Error 3 – Download was attempted to a different type drive i. Hz Sel Fault – F30 An unconnected adapter has been selected as the active frequency source.